You know that sinking feeling when you go to flush your toilet and it doesn’t go all the way down? It’s not a pleasant situation. But don’t worry, there are ways to fix this problem! Let me show you how.
Fixing Toilet Not Flushing All the Way
The first thing you’re going to want to do is to flush the toilet and hold down the handle until it flushes completely. Then check your tank for a floating device (if your toilet has one). This device floats and then shuts off the water when it reaches a certain level. If this piece is malfunctioning, then that’s what caused your toilet to not flush completely. If this piece is fine, then go ahead and check the chain attached to the handle if it’s too long or too short. Make sure that you adjust your chain so that it is at an optimal length for the best efficiency. Now, if all else fails…
You’re going to want to gently pull up on the flush handle and look at the chain attached to it that goes into the tank. If this piece has come unattached from where it’s supposed to be, you’ll want to reattach it by finding the open loop in which it belongs and hooking it back in there. That way when you pull up on your flush handle, the chain won’t be weighing it down and allow the water to flow completely to clean all the dirt.
Toilet not flushing all the way septic tank
If your toilet is not flushing all the way and using septic, then the reason for this problem is usually because there’s too much sludge built up in your septic tank. You’re going to want to have a professional come out and pump out your septic tank to get rid of all that excess sludge. That should do the trick!
Toto toilet not flushing all the way
If you have a Toto toilet and it’s not flushing all the way, then there is most likely an issue with your G-Max flushing mechanism. You’re going to want to review your owner’s manual or check out the Toto website to find out more information about how this feature works and why it may be malfunctioning. Usually, if this part is broken, the best thing to do is replace it.
Kohler toilet not flushing all the way
If you have a Kohler toilet and it’s not flushing all the way, then you’re going to want to check your chain and see if it’s too short or too long. Adjust the length of the chain so that it is at an optimal length for best effectiveness. You can also try gently pulling on your flush handle after your toilet has been flushed and see if the chain is connected to the Kohler flushing mechanism. If it’s not, reattach it there. That should do the trick.
New toilet not flushing all the way
If your toilet is new or less than a year old and it is not flushing all the way, then chances are the installation of the toilet was done improperly. You’ll want to contact someone who can come out and fix this for you so that your toilet flushes completely every time. It is also possible that your new toilet has an obstruction and you’ll want to shut off the water to your tank and flush it several times until you’re sure the obstruction has gone down. Then check your tank for damage if you notice anything out of the ordinary.
If your toilet is older than a year and you have tried adjusting your chain and it’s still not working, then try removing the water in your tank by holding down the handle until there is no more water in your tank. Then go ahead and flush it a few time to see if the water is going down all the way. If it doesn’t, then you’re going to want to check your flush valve for any damage and replace it if necessary.
Mansfield toilet not flushing all the way
If you have a Mansfield toilet and your flush valve is broken, then chances are replacing it will be the best solution. You’re going to want to shut off the water supply to your tank, disconnect your flush handle from the chain, remove it from the tank, check for obstructions or damage on both of these features if they exist, and then replace them if necessary.
Commercial toilet not flushing all the way
If you have a commercial toilet and it’s not flushing all the way, then there is probably something obstructing the flow of water to your tank. If this is the case, you’re going to want to shut off the water supply to your tank, disconnect it from the wall plumbing, flush it out until you notice that whatever was obstructing it is now gone, and then hook it all back up to the wall plumbing.
You can fix your commercial toilet’s flushing issues by using a plunger to try and unclog the water flow from your tank. Flush your toilet so that all of the water goes down, get a plunger and fit it over the drain hole at the bottom of your tank. Make sure you push hard on the plunger and then pull up quickly while still pushing down hard. This should work to unclog the water flow so that your toilet flushes all the way. if you have tried these methods and are still having problems with your Mansfield or commercial toilet not flushing all the way, then chances are it’s time to contact a plumber for help in fixing this issue.
Hope this article helped!
If you are looking for the best flushing toilet, check these reviews out.
Alex Kiangi is the Chief Editor here at Sleek Home HQ. He founded this site back in 2016 and in 2019, he joined hands with two other home improvement experts to focus on developing guides, reviews, and helpful material for anyone looking for reliable cleaning and toilet gear. Alex has over 12 years of experience as a home improvement expert and has worked with leading home improvement brands. He has a Masters Degree in Interior Design and an undergraduate degree in Economics. He started his career as a sales associate at Homes Depot and he has since worked with over 100 clients to assist them to improve their toilets.